Scrubo Pristine 26 Pro floor scrubber with the recovery tank open

How to Maintain Your Scrubo Floor Scrubber

A little regular care goes a long way. The steps below are taken from current Scrubo owner’s manuals, so you can keep tanks, squeegees, brushes and batteries in good shape — and catch small problems before they become downtime.

Always follow the manual for your exact model. Steps differ slightly between compact machines such as the Flex and Flex Plus and the larger walk-behind and ride-on scrubbers. Current English and French manuals are on each product page, and in our help centre.

Browse floor scrubbers  ·  Replacement parts  ·  Contact us

After each use: daily checks

On mid-size and large walk-behind and ride-on models — including the Pristine lineup and the CleanRider 26 — the manuals call for this routine after every use:

  • Drain and clean the recovery (dirty water) tank. Remove and rinse the float filter in that tank.
  • Drain the solution (clean water) tank. Rinse it if needed, using water no hotter than the limit in your manual.
  • Remove and clean the brushes or pads. Turn over or replace a worn pad.
  • Wipe the squeegee blades clean, check them for wear, and raise the squeegee when the machine is parked so the blades are not left bent or nicked.
  • Wipe the machine with a multipurpose cleaner and a damp cloth. Do not use high-pressure water or sprays, which can damage electronic parts.
  • Check the brush-head skirt and replace it if it is worn or damaged.
  • Charge the battery when you are finished (see charging habits below).

On the Flex and Flex Plus, the tanks come off the machine, which makes this easier. Empty both tanks into an appropriate drain, rinse them, and leave the caps slightly open so they can dry. The Flex Plus manual also has you flush the lines with 0.5 to 1 L of clean water in a full clean mode (brush, water and vacuum) before you put the machine away, and to empty the recovery tank every time you refill the solution tank. Store the machine in the upright park position.

Dispose of wastewater according to local rules.

Squeegee care

A clean squeegee in good condition is what leaves the floor dry. Wipe the blades after each use and check them for nicks and wear. Most Scrubo squeegees have a front blade and a rear blade.

  • When a blade is worn, turn or flip it to use a fresh edge the first time, then fit a new set. (Some special blades cannot be flipped — the Flex and Flex Plus manuals note this for blades with small arrow-like shapes. Replace those when they are worn.)
  • On walk-behind and ride-on machines, always raise the squeegee with the lift lever when the machine is not in use.
  • If the squeegee leaves streaks, clean the blades and check the angle and the suction hose for a blockage.

Replacement blades and squeegee parts are listed with our replacement parts.

Brushes and pads

Rinse brushes and pads after each use and replace them when they are worn. The Flex Plus manual, for example, says to replace brushes when the yellow wear indicator is at the same height as the other bristles. Worn, short bristles clean less well; waiting too long also makes the machine work harder.

Use the brush or pad that suits the floor, as described in your manual. Some models can use a pad driver as well as a brush. If your machine has a brush-pressure or water-flow control, set it for the job as the manual describes — lighter on delicate floors, and only as much pressure as you need on heavier soil.

Do not guess a replacement interval in months. Wear depends on the floor and how much you use the machine. Inspect often, and shop brushes, pads and other wear parts when you need them.

Tanks and filters

Do not overfill the tanks. On compact models, click removable tanks on firmly so the valve seals; a tank that is not seated properly is a common cause of little or no solution flow.

Filters are not the same on every machine, and they are not all on a weekly schedule:

  • Recovery-tank float filter (Pristine, CleanRider 26 and similar): remove and rinse it after each use.
  • Solution filter: clean it monthly on those same mid-size and large machines (the manuals also list this at about every 80 hours), or sooner if water flow is weak. Drain the solution tank first.
  • Flex and Flex Plus: if solution flow is poor, clean dirt from the solution tank and its filter. If recovery is poor, clean the squeegee opening and the foam filter, and clear the vacuum hose.
  • Polaris sweeper: this machine is a sweeper, not a scrubber. Shake the dust filter regularly while you work (the manual calls for about a minute every 30 minutes of sweeping), empty the dust box so it does not overfill, and check the filter for dust as scheduled in the Polaris manual.

Once a month on the mid-size and large scrubbers, also inspect and clean the recovery-tank cover seal, check for leaks, and check that nuts and bolts are tight. The manuals also have you lubricate pivots, rollers or wheels as described for that model.

Charging habits

Charging steps are not identical on every model, so use only the charger supplied with your machine and follow that model’s charging section. These habits appear across the current manuals:

  • Charge after use. Do not store the machine with a discharged battery, and do not leave a battery discharged for long periods.
  • Do not run the battery all the way down. On machines with a charge display, do not let all the lights or bars go out. On the Flex Plus, do not start a job with the battery below about 40%.
  • Charge in a well-ventilated area, on a level surface, with the machine switched off. On larger walk-behind and ride-on models, keep the battery compartment open (usually by tilting the recovery tank) while charging, as the manual shows.
  • Never pull the charging cable out while the charger is on. Switch off or unplug the charger first, then disconnect it from the machine.
  • If a battery shows swelling, cracks or leaks, stop using the machine and contact Scrubo.

Some compact models, including the Flex Plus, also ask you to charge the battery at least once a month even if the machine is not used, and to remove the battery for long storage (still charging it monthly). Before any cleaning or maintenance, switch the machine off and disconnect or remove the battery, as your manual describes.

Storage

  • Charge first, then drain and rinse both tanks.
  • Store the machine indoors in a dry place. Do not leave it in the rain or in a damp area.
  • Leave the recovery-tank cover or tank caps open so the tanks can air out.
  • On walk-behind and ride-on machines, store with the brush head raised and the squeegee up.
  • On the Flex and Flex Plus, use the upright park position, close to a wall, with the handle toward the wall and the brushes facing away from it.
  • In cold conditions, drain all liquid from the machine so it cannot freeze.

Quick troubleshooting

These checks come from the troubleshooting tables in the manuals. If a problem continues, contact Scrubo — most issues can be identified remotely.

  • The machine or brushes will not run. Charge the battery, check that it is installed or connected correctly, and, on larger machines, make sure the brush head is lowered. On a ride-on model, confirm the controls and safety interlocks are in the run position, as the manual describes.
  • Little or no solution flow. Fill the tank, make sure it is seated, open the water-flow control, and clean the solution filter and any blocked hose.
  • The floor is still wet, or recovery is weak. Empty a full recovery tank, lower the squeegee, clean or replace worn blades, check the cover seal, and clear the vacuum hose (and the foam filter on compact models).

Do not take motors or electrical parts apart yourself. Call 1-866-700-2023 or contact us.

Parts, manuals and support

English and French owner’s manuals are available as a download on each machine’s product page, and through the help centre. Watch how-to videos on our YouTube channel. Replacement brushes, pads, squeegee blades, filters and other parts are listed in replacement parts. If you do not see the part you need, email or call us.

Scrubo’s limited warranty covers electrical components on a parts-only basis for the original owner. For current terms, how to report an issue, and our Port Coquitlam service facility, see the warranty page. If you are not near headquarters, we can also help you find local service.

Make sure every operator has read the manual for that machine. Units ship 99% assembled, but correct daily care, charging and storage still matter. Our showroom and warehouse are at 1579 Kingsway Ave #1125, Port Coquitlam, BC (Monday–Friday 9:00 am–5:30 pm, Saturday 10:00 am–3:00 pm).

Shop replacement parts  ·  Help centre  ·  YouTube  ·  Contact us  ·  1-866-700-2023

Back to blog